I had the feeling that the Danmoto muffler I had modified for Minnie to go with my 2 -1 header set was the cause of the poor top end. Getting back to the dyno with a Megacycle muffler fitted proved to be a bit of an organisational nightmare, but I finally got there.
Red is the original headers and two of the Megacycle mufflers. Blue the 2-1 header with the Danmoto muffler from the previous. Green is the same as that run, but with one of the Megacycle mufflers instead of the Danmoto. Bit richer, more power - possibly different wideband sensor to the last runs (wacky?). Yellow is with Megacycle muffler and one of the airbox lid snorkels removed. Nowhere near as lean as the runs from last time with a snorkel out, not sure why. Maybe that was no air filter as well.
All of which means it dyno'd like it felt with the Megacycle muffler - better, and pulled through the top end nicer. Still down on power though.
An aside here is that when the bike was running the std 2 - 2 header set I didn't have a tacho fitted, and I'm sure I never went over 7,000 rpm. So that big jump in the std header curve, which happens at around 7,200 rpm, I may never have felt.
I took a std muffler with me for these dyno runs, and some Kokusan ignition units to replace the Ignitech. I have had intermittant cylinder dropping at idle when hot with this bike for years, across 2 engines now so I know it's not engine related. I thought I had swapped the Ignitech out without success in the past, but I must say that the issue has not reappeared with these Kokusan units fitted in the couple of times I have ridden Minnie since. To be fair to the Ignitech, it is the unit I originally bought back in 2006 or so. It's had a good run, and the new version has a dedicated MAP sensor input which works much better than trying to mimic a TPS with a map sensor. Maybe I just needed a reason to not feel bad about updating it.
Std muffler in blue, Danmoto in red and Megacycle in yellow. The air/fuel is a bit unexpected in as much as the red line seems a bit lean, but it may be a physically different sensor (I had two to choose from). Also you can see that an open muffler leans it out. I had thought that maybe these carbs would richen up with an open muffler due to the way CV carbs work, but I'm still not convinced this was a good test. Danmoto is still better than std! For an illustration of the hollowness of that victory, see the following graph.
Anyway, onward into the slurry. Red is std muffler as before, blue is Megacycle muffler with Ignitech ignition, green is Megacycle muffler with Kokusan ignition and yellow is Megacycle muffler with Kokusan ignition and one snorkel pulled from the airbox lid. Helps with the richness.
Comparing headers only (std versus my 2 - 1), first up std mufflers.
And the Megacycle mufflers. The point where the two curves cross is bang on 7,000 rpm.
So, some conclusions of sorts.
1/ The Danmoto muffler I really like doesn't work.
1/ The Danmoto muffler I really like doesn't work.
2/ The 2-1 header I made doesn't work.
3/ It's too rich at the top end. From my test of watching the slides lift through the airbox lid I think i'll call it a main jet issue. If pulling the other snorkel fixed that without hurting the midrange I'd be all over it, but as that wishful plan didn't pan out I'll ignore it for as long as I can't be arsed pulling the airbox out.
4/ Original headers don't work anymore due to the lack of muffler mounts due to the Ducabike rearsets. And the vertical header has been shortened, so any main header will need to be cut, bent and welded as this 2 - 1 header was for them to join. I did find another original vertical header at work, so I could fit that.
5/ One has dug oneself a hole.
I think I'll need to refit some 2 - 2 headers, as the next step is some 620 cams modified to fit the old 3 bearings heads.
No comments:
Post a Comment